- Home
- Conversions
- Major Appliances
- Auxiliary Heating
- Propex Heatsource HS2000E Gas 12V 24...
Propex Heatsource HS2000E Gas 12V 240 Volt (European Fitting Only)
JK Part Number: J20285
Purchase Information
Availability:
Special Order. This product is available on a special order basis. If your item is built to specification we will contact you for the details.
Expected Delivery:
About 13 days
Please Note:
Once placed Special Orders cannot be cancelled
Delivery:
Mainland UK Only. For overseas and international shipping call +44 (0)1256 862288
Product Description
If you’re looking for intuitive, automatic central heating for your campervan, then the Propex HS2000E Blown Air Heater is the ideal unit for your vehicle. This automatic, thermostatically controlled blown air heating system fuelled by propane / butane gas or 230V mains electric, works to ensure you’re always warm, day or night.
One key benefit is that the setup allows for much greater versatility between the two power sources, helping to conserve your gas supply when on sites with electricity available.
Please be aware these heaters are rated for use with 30mb butane and 30/37mb propane. This is widely acceptable across Europe, though some European countries also use 50mb gas pressure. These are not suitable for use in the USA.
As standard, the HS2000E is supplied with a solid state electronic thermostat which automatically switches the unit on and off. This means it’s effortless to maintain a desired temperature in your camper, no matter the time of day. If the temperature reaches below the set level, the Heatsource will automatically ignite and run until the cabin reaches the desired temperature.
The thermostat’s easy-to-install surface mount design effortlessly integrates with the new electronics fitted to the HS2000E heaters. It’s simple, intuitive controls mean it’s easy to switch between the gas and electric modes, and its constant heater feedback loop enable quick and easy system diagnosis.
Fortunately, it also has selectable electric hook up power levels to ensure you do not overload your available supply.
For optimal gas efficiency, the unit makes use of forced air combustion and the Propex two stage stainless steel heat exchanger for a clean and efficient way to heat your camper.
The air for the combustion is taken from outside of your vehicle and passed into the combustion chamber. Having been mixed with gas during three aeration stages, it is ignited automatically and heats up the large surface area of the heat exchanger.
The Heatsource HS2000E heater units are totally room sealed and exhaust all products of combustion externally through the neat 22mm i.d. stainless steel flue pipe. Making it even more efficient, cabin air is normally re-circulated in preference to using cold air from outside.
The HS series heaters are very efficient on 12 volt electrical consumption, drawing less than 1.7 amps on gas operation or 2.2 amps during mains operation.
When it comes to mains electrics efficiency, for those using a mains hook up, there is the option of using the powerful electric element with efficient heat exchanger built in.
Three settings are available, giving 500W, 1KW or 2KW of heat output and drawing a maximum current of 9 amps. The motor speed is altered to suit each power level, ensuring maximum efficiency or, when on low 500W setting, keeping motor and air noise to a minimum when running overnight.
The heater is supplied with a mains cable and moulded 3 pin plug.
No-one wants noisy central heating – Propex heaters are designed to be quiet in operation without compromising air throughput and heat output. There will always be some air noise from a system that produces a healthy throughput of air, however, by using high quality balanced fans and smooth enclosed motors with ball race bearings, noise is significantly reduced.
Noise from the heater is also unaffected by high voltage, a common occurrence with battery chargers, solar panels etc that are permanently wired. The microprocessor electronics regulates the motor voltage so that the fan speed does not alter between 10 and 15 volts.
Heatsource blown air heaters conform to the latest European standards for both the appliance and the electronics. During the rigorous testing, the focus is very much on safety. The heaters also have to comply with an enhanced version of the Electro Mechanical Compatibility Directive, to ensure they do not interfere with other electronics.
Thanks to its intelligent electronics, the unit continuously monitors the operation of the heater to make sure everything is operating correctly and safely. This includes monitoring of the flame, case temperature, combustion airflow, gas solenoid valve and voltage. Should any of these move outside of the predetermined levels, the heater will immediately be switched off and the red light on the thermostat will indicate a fault by flashing a certain number of times.
The HS2000E blown air heater is supplied with complete fitting kits to suit vehicle use. In vehicles, the unit is usually subtly mounted in a bed box or cupboard, flued downwards through the floor and out to the side of the camper using flexible stainless ducting.
These ducts (22mm internal diameter) are supplied as standard in lengths of 750mm. The ends are finished with neat stainless steel end caps which comply with EN624.
The heat is ducted to one or more outlets through the tough, highly flexible 60mm ducting. In the case of multi-outlet installations, the first outlet is an open outlet with directional control and the rest are closable, used in conjunction with the appropriately sized plastic Y branches.
The information below indicates the consumption of gas if the heater is running continuously.
HS2000 Average Consumption 142 grams/hour –
3.9 kg propane cylinder 27.5 hours
4.5 kg butane 31.7 hours
13kg propane 91.5 hours
15kg butane 105.6 hours
19kg butane 133.8 hours
47kg butane 331.0 hours
904 Camping Gaz (1.81kg) 12.75 hours
907 Camping Gaz (2.72kg) 19.0 hours
Technical Specifications –
HS2000: Gas Electric Heat Input: 2.0kw
Heat Output: 1.9kw 500w, 1KW, 2KW
Voltage: 12v or 24v versions 230 volts a.c. 50 Hz
Current Consumption: 1.4A cont' running 9 A max' current air throughput: 60 C.F.M. 60 C.F.M.
Fuel: Butane or Propane Mains Electric
Specification
Country of Manufacture | United Kingdom |
---|---|
EAN / UPC | Propex Heatsource HS2000E Gas 12V 240 Volt (European Fitting Only) |
Finance Available on This Product | Yes |
Width (CM - Packed) | 27.0 |
Height (CM - Packed) | 25.5 |
Depth (CM - Packed) | 76.0 |
Shipping To Mainland UK Only | Yes |
Manufacturer | Propex |
Special Order | Yes |
Special Order Lead time | 13 |
Vehicle Compatability
VW T2 Split Screen
Air-Cooled Petrol (1950 - 1967) :
1200cc, 1500cc
LHD, RHD
VW T2 Bay Window
Air-Cooled Petrol (1967 - 1979) :
1600cc, 1700cc, 1800cc, 2000cc
LHD, RHD
VW T25
Water-Cooled & Air-Cooled Petrol (1979 - 1992) :
1600cc, 1700cc, 1900cc, 2000cc, 2100cc
LHD, RHD
Water-Cooled & Air-Cooled Diesel (1979 - 1992) :
1600cc, 1700cc, 1900cc, 2000cc, 2100cc
LHD, RHD
VW T4
Water-Cooled Petrol (1990 - 2003) :
1800cc, 1900cc, 2000cc, 2400cc, 2500cc, 2800cc
LHD, RHD
Water-Cooled Diesel (1990 - 2003) :
1800cc, 1900cc, 2000cc, 2400cc, 2500cc, 2800cc
LHD, RHD
VW T2c Brazilian Bay Window
Water-Cooled & Air-Cooled Petrol (1997 - 2013) :
1400cc, 1600cc
LHD, RHD
VW T5
Water-Cooled Petrol (2003 - 2015) :
1900cc, 2000cc, 2500cc, 3200cc
LHD, RHD
Water-Cooled Diesel (2003 - 2015) :
1900cc, 2000cc, 2500cc, 3200cc
LHD, RHD
VW T6
Water-Cooled Diesel (2015 - 2021) :
2000cc
LHD, RHD
Fitting Guide (PDF)
Write a review
Seen This Product Cheaper Elsewhere?
If you have seen the same product cheaper elsewhere then please let us know.
Purchase Information
Availability:
Special Order. This product is available on a special order basis. If your item is built to specification we will contact you for the details.
Expected Delivery:
About 13 days
Please Note:
Once placed Special Orders cannot be cancelled
Delivery:
Mainland UK Only. For overseas and international shipping call +44 (0)1256 862288
If you’re looking for intuitive, automatic central heating for your campervan, then the Propex HS2000E Blown Air Heater is the ideal unit for your vehicle. This automatic, thermostatically controlled blown air heating system fuelled by propane / butane gas or 230V mains electric, works to ensure you’re always warm, day or night.
One key benefit is that the setup allows for much greater versatility between the two power sources, helping to conserve your gas supply when on sites with electricity available.
Please be aware these heaters are rated for use with 30mb butane and 30/37mb propane. This is widely acceptable across Europe, though some European countries also use 50mb gas pressure. These are not suitable for use in the USA.
As standard, the HS2000E is supplied with a solid state electronic thermostat which automatically switches the unit on and off. This means it’s effortless to maintain a desired temperature in your camper, no matter the time of day. If the temperature reaches below the set level, the Heatsource will automatically ignite and run until the cabin reaches the desired temperature.
The thermostat’s easy-to-install surface mount design effortlessly integrates with the new electronics fitted to the HS2000E heaters. It’s simple, intuitive controls mean it’s easy to switch between the gas and electric modes, and its constant heater feedback loop enable quick and easy system diagnosis.
Fortunately, it also has selectable electric hook up power levels to ensure you do not overload your available supply.
For optimal gas efficiency, the unit makes use of forced air combustion and the Propex two stage stainless steel heat exchanger for a clean and efficient way to heat your camper.
The air for the combustion is taken from outside of your vehicle and passed into the combustion chamber. Having been mixed with gas during three aeration stages, it is ignited automatically and heats up the large surface area of the heat exchanger.
The Heatsource HS2000E heater units are totally room sealed and exhaust all products of combustion externally through the neat 22mm i.d. stainless steel flue pipe. Making it even more efficient, cabin air is normally re-circulated in preference to using cold air from outside.
The HS series heaters are very efficient on 12 volt electrical consumption, drawing less than 1.7 amps on gas operation or 2.2 amps during mains operation.
When it comes to mains electrics efficiency, for those using a mains hook up, there is the option of using the powerful electric element with efficient heat exchanger built in.
Three settings are available, giving 500W, 1KW or 2KW of heat output and drawing a maximum current of 9 amps. The motor speed is altered to suit each power level, ensuring maximum efficiency or, when on low 500W setting, keeping motor and air noise to a minimum when running overnight.
The heater is supplied with a mains cable and moulded 3 pin plug.
No-one wants noisy central heating – Propex heaters are designed to be quiet in operation without compromising air throughput and heat output. There will always be some air noise from a system that produces a healthy throughput of air, however, by using high quality balanced fans and smooth enclosed motors with ball race bearings, noise is significantly reduced.
Noise from the heater is also unaffected by high voltage, a common occurrence with battery chargers, solar panels etc that are permanently wired. The microprocessor electronics regulates the motor voltage so that the fan speed does not alter between 10 and 15 volts.
Heatsource blown air heaters conform to the latest European standards for both the appliance and the electronics. During the rigorous testing, the focus is very much on safety. The heaters also have to comply with an enhanced version of the Electro Mechanical Compatibility Directive, to ensure they do not interfere with other electronics.
Thanks to its intelligent electronics, the unit continuously monitors the operation of the heater to make sure everything is operating correctly and safely. This includes monitoring of the flame, case temperature, combustion airflow, gas solenoid valve and voltage. Should any of these move outside of the predetermined levels, the heater will immediately be switched off and the red light on the thermostat will indicate a fault by flashing a certain number of times.
The HS2000E blown air heater is supplied with complete fitting kits to suit vehicle use. In vehicles, the unit is usually subtly mounted in a bed box or cupboard, flued downwards through the floor and out to the side of the camper using flexible stainless ducting.
These ducts (22mm internal diameter) are supplied as standard in lengths of 750mm. The ends are finished with neat stainless steel end caps which comply with EN624.
The heat is ducted to one or more outlets through the tough, highly flexible 60mm ducting. In the case of multi-outlet installations, the first outlet is an open outlet with directional control and the rest are closable, used in conjunction with the appropriately sized plastic Y branches.
The information below indicates the consumption of gas if the heater is running continuously.
HS2000 Average Consumption 142 grams/hour –
3.9 kg propane cylinder 27.5 hours
4.5 kg butane 31.7 hours
13kg propane 91.5 hours
15kg butane 105.6 hours
19kg butane 133.8 hours
47kg butane 331.0 hours
904 Camping Gaz (1.81kg) 12.75 hours
907 Camping Gaz (2.72kg) 19.0 hours
Technical Specifications –
HS2000: Gas Electric Heat Input: 2.0kw
Heat Output: 1.9kw 500w, 1KW, 2KW
Voltage: 12v or 24v versions 230 volts a.c. 50 Hz
Current Consumption: 1.4A cont' running 9 A max' current air throughput: 60 C.F.M. 60 C.F.M.
Fuel: Butane or Propane Mains Electric
Country of Manufacture | United Kingdom |
---|---|
EAN / UPC | Propex Heatsource HS2000E Gas 12V 240 Volt (European Fitting Only) |
Finance Available on This Product | Yes |
Width (CM - Packed) | 27.0 |
Height (CM - Packed) | 25.5 |
Depth (CM - Packed) | 76.0 |
Shipping To Mainland UK Only | Yes |
Manufacturer | Propex |
Additional Carriage Charge | 0.0 |
Special Order | Yes |
Special Order Lead time | 13 |
VW T2 Split Screen
Air-Cooled Petrol (1950 - 1967) :
1200cc, 1500cc
LHD, RHD
VW T2 Bay Window
Air-Cooled Petrol (1967 - 1979) :
1600cc, 1700cc, 1800cc, 2000cc
LHD, RHD
VW T25
Water-Cooled & Air-Cooled Petrol (1979 - 1992) :
1600cc, 1700cc, 1900cc, 2000cc, 2100cc
LHD, RHD
Water-Cooled & Air-Cooled Diesel (1979 - 1992) :
1600cc, 1700cc, 1900cc, 2000cc, 2100cc
LHD, RHD
VW T4
Water-Cooled Petrol (1990 - 2003) :
1800cc, 1900cc, 2000cc, 2400cc, 2500cc, 2800cc
LHD, RHD
Water-Cooled Diesel (1990 - 2003) :
1800cc, 1900cc, 2000cc, 2400cc, 2500cc, 2800cc
LHD, RHD
VW T2c Brazilian Bay Window
Water-Cooled & Air-Cooled Petrol (1997 - 2013) :
1400cc, 1600cc
LHD, RHD
VW T5
Water-Cooled Petrol (2003 - 2015) :
1900cc, 2000cc, 2500cc, 3200cc
LHD, RHD
Water-Cooled Diesel (2003 - 2015) :
1900cc, 2000cc, 2500cc, 3200cc
LHD, RHD
VW T6
Water-Cooled Diesel (2015 - 2021) :
2000cc
LHD, RHD
Seen This Product Cheaper Elsewhere?
If you have seen the same product cheaper elsewhere then please let us know.
Shopping Finance
General Information
Interest free credit is available on all purchases of £350 or more. You can apply online – it's quick, easy and you'll get an instant decision. Our online retail finance partner is Divido. Credit is provided subject to status.
Example Finance Options
Cash Price: £676.00
Deposit: £70.00
Credit Amount: £606.00
12 Monthly Installments of £50.50
Typical APR: 0%
How To Apply
Visit our web-site and select the items you wish to purchase. At the check out screen select "Finance" as your payment option.It only takes a couple of minutes and you get an instant decision.
Criteria
To apply for finance you must meet the following criteria;
- You must be over 18 years of age.
- You must be a UK resident with at least 3 years continual address history.
- You must be in full time employment, unless retired or a house person with a spouse in full time employment.
- You must have a UK bank account capable of accepting Direct Debits.
- The goods must be delivered to your home address.
Benefits
- Interest free credit is available on all purchases over £350.
- Buy the items you want now + accessories, all for a low monthly payment.
- Choose a higher-spec item for a few pounds more per month.
- You can spread the cost of your purchase to minimise your monthly payments.
- One-stop shopping: no need to go to a bank to secure funding.
- Keep cash for day-to-day expenses.
- Fixed repayments — your payments are fixed for the duration of the agreement allowing you to budget more effectively.
How Much Can I Borrow?
When checking out, just fill out our easy online application form and you can be approved for up to £5,000 to use for the item(s) you wish to purchase. The minimum order is £350.
Is A Deposit Required?
A minimum deposit of 10% is required and is payable by credit or debit card upon acceptance.
How Are My Monthly Payments Paid?
All monthly payments are paid by direct debit from your personal bank account. Typically the first payment will be due one month after the date of the finance agreement and subsequent monthly payments will be due every month for the length of your term on that day of the month.
What Length of Repayment is Available?
You can currently choose a 6 or 12 month loan repayment period at 0% APR depending on the value of your order.
Can I Pay My Agreement Off Early?
You can settle your loan agreement at any time. Simply write to Shawbrook and they will calculate and send you, your settlement figure. Your settlement figure and date are calculated in line with the Consumer Credit Act.
Exclusions
0% Finance is currently not available for engines, gearboxes and any item that requires a deposit.
Available to retail customers only and excludes any other offers.
Finance Cancellations
You can return all the items ordered on finance and the policy can then be cancelled. This will incur a 10% handling fee to cover the cost of the finance agreement.
Finance Item Replacements
We will replace any faulty or damaged item ordered on finance free of charge.
Finance Item Cancellations
If you wish to cancel an item ordered on finance but keep the rest of the order, we will refund the cost of the item by means of a cheque and the finance agreement will remain in place between you and the finance company. A 10% handling fee will be charged to cover the cost of the finance agreement.