Propex HS2800 Interior 12v Heating System (European Fitting Only)
JK Part Number: J27697
The HS2800 heaters are automatic thermostatically controlled blown air heating systems fuelled by propane or butane gas. The HS2800 with its greater heat output of 2.8kW and twin outlet is the big brother to the smaller output, single outlet HS2000. Heatsource is designed for a variety of automotive and marine applications as a source of heat totally independent of the engine. Control:The HS2800 is supplied as standard with a solid state electronic thermostat which automatically switches the unit on and off to maintain the desired temperature. When the room temperature drops below the selected level, the Heatsource will automatically ignite and run until the cabin reaches the selected temperature. The thermostat is an easy to fit surface mount design and integrates with the new electronics fitted to the HS2800 heaters. An easy to operate panel mounted digital timer / thermostat specifically designed for heatsource, is also available as an optional extra. Unlike some heaters, there is minimal electric current consumption during ignition so cycling the heatsource on and off does not have the effect of additional battery drain. Efficiency: With forced air combustion and the Propex two stage stainless steel heat-exchanger, the HS2800 is a clean and highly efficient way to heat your vehicle or boat. Air for combustion is taken from outside and passed into the combustion chamber having been mixed with gas during three aeration stages, it is ignited automatically and heats up the large surface area of the heat-exchanger. The Heatsource units are totally room sealed and exhaust all products of combustion externally through the neat 22mm i.d. stainless steels flue pipe. To add to the efficiency, cabin air is normally re-circulated in preference to using cold air from outside. The HS series heaters are also very efficient on electrical current consumption, the high quality motor/fan combination and innovative current reducing electronics, both of which have been improved in the latest versions, means that even the larger HS2800 draws less than 2 amps during normal operation. Quiet Operation: Propex heaters are designed to be quiet in operation without compromising air throughput and heat output. There will always be some air noise from a system that produces a healthy throughput of air, however, by using high quality balanced fans and smooth enclosed motors with ball race bearings, noise is kept to a minimum. Noise is also unaffected by high voltage, a common occurrence with battery charges, solar panels etc permanently wired. The micro-processor electronics regulates the motor voltage so that the fan speed does not alter from 10 to 15 volts. Safety: Heatsource blown air heaters conform to the latest European standards for both the appliance and the electronics and during the rigorous testing the focus is very much on safety. The heaters also have to comply with an enhanced version of the Electro Mechanical Compatibility Directive to ensure they do not interfere with other electronics and that they are immune from interference by other electronics. The intelligent electronics are continuously monitoring the operation of the heater to make sure everything is operating correctly and safely. This includes monitoring of the flame, case temperature, combustion airflow, gas solenoid valve and voltage. Should any of these stray outside of the predetermined levels, the heater will be switched off and the red light on the thermostat will indicate a fault by flashing a certain number of times. Installation: The HS2800 is supplied with complete fitting kits to suit either vehicle applications. In vehicles and caravans the unit is usually mounted in a bed-box or cupboard, flued downwards through the floor and out to the side of the vehicle using flexible stainless ducting. These ducts (26mm i.d. for the HS2800) are supplied as standard in lengths of 750mm for vehicles. The ends are finished with neat stainless steel end-caps which comply with EN624. The heat is ducted to one or more outlets through tough highly flexible 60mm or 76mm ducting. In the case of multi-outlet installations, the first outlet is an open outlet with directional control and the rest are closable and are used in conjunction with the appropriate sized plastic Y-branches. Please be aware these heaters are rated for use with 30mb butane and 30/37mb propane. This is widely acceptable across Europe though some European countries also use 50mb gas pressure.
Heat Input: 3.0kW
Heat Output: 2.8kW
Voltage: 12V version
Current Consumption: 1.9A continuous running
Air Throughput: 85 C.F.M.
Fuel: Butane or Propane Gas
HS2800 Economy & Consumption
The information below reflects the consumption of gas if the heater was running continuously.
Average Consumption: 225grams/hour
3.9kg Propane Cylinder: 17.5 hours
4.5kg Butane: 20 hours
13kg Propane: 58 hours
15kg Butane: 67 hours
19kg Butane: 84.5 hours
47kg Butane: 209 hours
904 Camping Gaz (1.81kg): 8 hours
907 Camping Gaz (2.72kg): 12.0 hours
|Country of Manufacture||United Kingdom|
|Width (CM - Packed)||33.0|
|Height (CM - Packed)||52.0|
|Depth (CM - Packed)||30.0|
|Shipping To Mainland UK Only||Yes|
|Additional Carriage Charge||0.0|
|Special Order Lead time||10|
Customer Reviews (0)Write a review
No reviews have been written for this product yet
Products and packaging are subject to change or substitution without prior notice. Every effort will be made to despatch the product specified. However in the event of supply difficulties with any products listed, we reserve the right to substitute goods without prior notice.
Seen This Product Cheaper Elsewhere?
If you have seen the same product cheaper elsewhere then please let us know.